Vadzo Imaging Launches Armor-2020CRS-FPD3: 20MP Color FPD-Link III Camera for High Resolution Color Imaging in Embedded Vision Systems

via ACCESS Newswire
ⓘ This article is third-party content and does not represent the views of this site. We make no guarantees regarding its accuracy or completeness.

FORT WORTH, TX / ACCESS Newswire / November 20, 2026 / Vadzo Imaging, a provider of embedded vision camera products for OEMs and system integrators, today launches the Armor-2020CRS-FPD3, a 20MP Color FPD-Link III Camera built on the Onsemi AR2020 sensor. Part of Vadzo's SerDes camera portfolio, it combines 20MP color resolution, Hyperlux LP low-light performance, and FPD-Link III long-distance transmission with a single-cable design, low-latency streaming, and multi-camera readiness. Vadzo presents an AR2020 Color FPD-Link III Camera and a 20MP Rolling Shutter FPD-Link III Camera for robots, vehicles, transportation systems, inspection stations, and surveillance systems, together with guidance on bandwidth, power, and platform choice.

Why a 20MP Color FPD-Link III Camera Must Match Its Link, Its Light, and Its Host

Resolution is the easiest specification to want and the hardest to deliver on a real platform. A 20MP color frame holds more than twice the pixels of a 4K frame, and every pixel must be captured, sent, received, and processed. Perception software benefits, since distant signs, plates, faces, and defects cover more pixels, and wide scenes can be watched by one unit that would otherwise need several. The cost lands on the link, the host, and the power budget, and a design that ignores it discovers the limit late, when the frame rate it needs does not fit the cable it chose.

Distance is the second problem. The platforms that want this detail rarely have room for a computer at the camera. A mobile robot keeps its computer low and protected, and its camera high for a good view. A vehicle puts its processor in a cabin or a trunk and its camera units at the corners. A traffic pole holds the camera meters above the cabinet. A short parallel ribbon cable cannot span these distances, and a long one carries noise, adds weight, and fails at connectors. A serial link solves the distance by turning many parallel signals into one fast stream that travels over coaxial cable.

Light is the third. Embedded systems work at dusk, in shade, in tunnels, and under uneven lamps, and a 20MP sensor has small pixels, so each collects less light than the pixels of a lower-resolution sensor of the same size. Dim scenes show noise, and noise hides the very detail that high resolution is meant to capture. Back-illuminated pixels, a lens with a wide aperture, and steady lighting all help, and the designer must judge how much of the sensor's resolution the scene will let the camera use.

Integration is the fourth. Teams want one cable to carry video, control, and power, so that installation is quick and wiring failures are rare. They want the camera to join synchronized sets of units for surround views and wide area coverage. They want the delay between the scene and the decision to stay small, and they want a body that survives vibration, heat, and dust. Teams that choose a camera for one of these needs and discover the others later must redesign after the hardware is built, and a clear view of all four at the start saves much of that work.

How a 20MP Color FPD-Link III Camera Brings High Resolution Over One Cable

The Armor-2020CRS-FPD3 is built on the Onsemi AR2020, a 20MP (5120 x 3840) color rolling shutter sensor with a 1/1.8 inch optical format and 1.4 micron pixels, in the Hyperlux LP back-illuminated design. Back illumination routes light to the photodiode from the rear of the silicon, which improves light collection. The sensor reads the image row by row, so the camera uses a rolling shutter, which suits most scenes and can show skew on very fast motion or strong vibration. A serializer on the camera converts the sensor's parallel output into a high-speed serial stream, and a deserializer on the host converts it back into a standard camera interface. FPD-Link III is the serializer and deserializer family of Texas Instruments, and it carries video on a forward channel over coaxial cable or shielded twisted pair, with control commands travelling in the opposite direction on a slower back channel.

A short calculation shows what 20MP means for such a link. A full frame at 10 bits per pixel is about 197 million bits, and at 12 bits about 236 million bits. The higher-speed FPD-Link III devices carry video at a forward rate of about 4 gigabits per second, a figure teams should confirm for the serializer in use. At 12 bits per pixel, 15 frames per second needs about 3.5 gigabits per second and fits, while 30 frames per second needs about 7.1 gigabits per second and does not. At 8 bits per pixel, 30 frames per second needs about 4.7 gigabits per second, which still exceeds the rate. The practical consequences are a choice of modes. A team can run full resolution at a lower frame rate, use a 4K or other reduced mode when speed matters, crop a region of interest, or use more than one link. The figures are illustrative, since real streams depend on the output format and on protocol overhead, and teams should confirm the available modes against the product documentation.

The single cable design carries video, control data, and power on one coaxial cable, so there is no separate power run to the camera. Power over a long cable loses voltage in proportion to the current. For example, a run with 1.5 ohms of round-trip resistance drops about 0.4 volts at 0.25 amperes, and the camera and the supply must tolerate that drop, so teams should confirm the power budget and the voltage range for their cable length. The same cable also carries the commands that set the exposure and gain, read the sensor, and trigger frame capture, which is why the control channel matters as much as the video channel. A rugged build, with a secure connector and a sealed or supported housing, keeps the link working under vibration.

Latency depends on the whole chain. The serializer and deserializer add very little delay, since the transfer is direct and carries no compression. The larger parts are the exposure and the readout of the sensor, which for a 20MP frame can take tens of milliseconds, and the processing on the host. Teams that need fast decisions should measure the full path, for example by filming a running timer on a display, and should consider a smaller mode or a cropped region when speed matters more than detail. Where several camera units work together, frame synchronization signals sent over the control channel can start the units at the same moment, so that their frames line up in time.

The host side needs care. A Jetson module reads camera modules through MIPI CSI-2 lanes, so an FPD-Link III camera needs a deserializer board that converts the serial stream back into MIPI CSI-2 and connects to the module, and teams should confirm which board Vadzo supplies for the platform they use. A multi-port deserializer can accept several camera links, and the total data must fit the lanes of the module. For example, four units each sending 20MP frames at 12 bits per pixel and 5 frames per second would deliver about 4.7 gigabits per second to the host, and at 15 frames per second about 14 gigabits per second, which many modules cannot take. The camera supports NVIDIA Jetson Orin platforms, and teams should confirm drivers, lane settings, and frame rates for each module they plan to use, including the Orin Nano, the Orin NX, and the AGX Orin.

Light and resolution trade against each other, and a short comparison shows how. A 20MP sensor with 1.4 micron pixels collects about one fifth of the light per pixel that a 2MP sensor with 3 micron pixels would collect from the same lens and scene, since the pixel area is about 4.6 times smaller. Combining 2 by 2 neighboring pixels in a lower resolution mode recovers part of that light and lowers noise, at the cost of detail. The module therefore serves as both a detailed camera in good light and a more sensitive camera in dim light, if the mode is chosen to suit the scene, and a lens with a wide aperture and a clean front element helps in either case. Teams should test at the darkest light they expect and compare the modes on real footage.

A worked example shows how resolution, lens, and link fit together. Suppose a camera on a traffic pole must read a license plate 0.3 meters wide at a distance of 30 meters, with 40 pixels across the plate for reliable reading. Each pixel must then cover 7.5 millimeters at that range, which is an angle of 0.25 milliradians. With 1.4-micron pixels, that calls for a lens with a focal length of about 5.6 millimeters, and the 5120 pixels across the sensor then cover a width of about 38 meters at 30 meters, ignoring lens distortion. A 4K mode with 3840 pixels across would cover about 29 meters with the same lens. The stream matters too. Full frames at 12 bits and 15 frames per second need about 3.5 gigabits per second and fit the link, so the design can use the full field and still read plates on vehicles that cross it. The figures are illustrative, and a real design must account for vehicle speed, exposure, and lens distortion.

A short evaluation plan helps teams avoid surprises. They should mount the camera on the real platform with the real cable, record in the darkest and brightest conditions the system will meet, and measure the frame rate, the delay, and the voltage at the camera in each mode. They should repeat the test with the full number of camera units, since the load on the host grows with each unit, and they should leave the system running for a long period to see how the link and the module behave as they warm up. Problems with connectors, cable bends, and power usually show up in such a test long before they show up on a bench, and Vadzo can review the results with a customer during evaluation so that the first production unit behaves like the one on the test rig.

Product Overview: 20MP Color FPD-Link III Camera for Embedded Vision Systems

The Armor-2020CRS-FPD3 is a 20MP color FPD-Link III module built on the Onsemi AR2020 sensor. As a 20MP Orin FPD-Link III Camera, it connects to NVIDIA Jetson Orin platforms through a deserializer board, and as a 20MP Low-Light FPD-Link III Camera, it offers back-illuminated pixels for dim scenes. The AR2020 FPD-Link III Camera designation covers its sensor and its link. The module also serves as an AR2020 Rolling Shutter FPD-Link III Camera, an AR2020 Orin FPD-Link III Camera, an AR2020 Jetson FPD-Link III Camera, a 20MP Jetson Orin FPD-Link III Camera, an AR2020 Low-Light FPD-Link III Camera, a 20MP Color Low-Light FPD-Link III Camera, an AR2020 Color Low-Light FPD-Link III Camera, and a 20MP FPD-Link III Camera Module for designs that need a long, robust link. It is also an Embedded Vision FPD-Link III Camera, a High-Resolution FPD-Link III Camera, a Color Imaging FPD-Link III Camera, an Embedded Imaging FPD-Link III Camera, and a Color Vision FPD-Link III Camera for engineers who build perception systems.

Key Capabilities of the 20MP Color FPD-Link III Camera

Key specs: 20MP (5120 x 3840) Max Resolution | Onsemi AR2020 1/1.8 inch Sensor Format | 1.4 micron Pixel | Color with Rolling Shutter | FPD-Link III SerDes Interface | Lens per Module Configuration

20MP Color Resolution

The sensor captures fine detail at 5120 x 3840 in color, which suits inspection, analytics, and wide-area monitoring, since small objects such as signs, plates, defects, and faces cover many pixels. A rolling shutter reads the image row by row, which gives high resolution and good sensitivity at reasonable cost, and fast motion or strong vibration can cause slight skew, which a short exposure reduces. Vadzo offers global shutter modules for platforms where fast motion is the main concern. Teams should confirm the available modes and frame rates.

Hyperlux LP Low Light Performance

Hyperlux LP back-illuminated pixels deliver clean color images in dim scenes with low noise, since back illumination improves light collection. The pixels are small, at 1.4 microns, so a lens with a wide aperture and steady illumination help considerably, and combining neighboring pixels in a lower resolution mode trades detail for sensitivity. Where light can be added safely, a modest increase usually improves the image more than any setting. Teams should test at the darkest light they expect.

Long Distance Transmission

FPD-Link III sends high-speed video over coaxial cable across long runs between the module and the host, which lets the camera sit where the view is and the computer where it is protected. The forward rate is lower than that of some other serial links, so the full 20MP frame at a high frame rate needs more than one link carries, and teams should choose the mode and the frame rate to match the link. Teams should confirm the cable length and the connector for their design.

Single Cable Design

Video, control data, and power travel on one cable, which reduces wiring and installation time and removes a separate power run to the camera. A long cable drops voltage as current flows, so the power budget and the voltage range should be checked for the real run. As a 20MP FPD-Link III Camera Manufacturer and an AR2020 FPD-Link III Camera Supplier, Vadzo supports deserializer selection, cable planning, and enclosure design for volume programs.

Low Latency Streaming

Direct SerDes transfer keeps the delay added by the link low, which suits real-time decisions in moving systems, since the stream is not compressed. The sensor readout and the host processing usually add more, so the whole chain should be measured, for example by filming a running timer on a display, and a reduced mode can cut the delay when speed matters more than detail.

Multi Camera Readiness

The module works with multi-port deserializers for synchronized multi-camera setups, so frames from several units can be compared at the same moment, which surround views and wide-area coverage need. The total bandwidth into the host must fit its lanes, and teams should plan it before choosing the number of units and the frame rate of each.

Rugged Armor Build

The module is designed for vibration and harsh field conditions in automotive and industrial use. Teams should confirm the environmental ratings in the product documentation, secure the connector against vibration with the right cable and strain relief, and test the module on the real platform, since a cable that passes on the bench can behave differently beside a motor or an inverter.

NVIDIA Jetson Orin Platform Support

The module supports NVIDIA Jetson Orin platforms, so a team can choose a compact module for a small robot or a larger one for heavy models without changing the camera. A deserializer board converts the serial stream into MIPI CSI-2 for the module, and teams should confirm the board, the drivers, and the lane settings for each Orin module they plan to use.

"Twenty megapixels is a promise of detail, and the link decides how much of it arrives. The Armor-2020CRS-FPD3 puts that detail on one coaxial cable that also carries control and power, with Hyperlux LP pixels for dim scenes and a rugged body for the field. We are plain about the limits. FPD-Link III carries less than some other serial links, so full resolution at a high frame rate needs more than one link provides; the mode and the frame rate must be chosen together, and long cables drop voltage. A Jetson also needs a deserializer board. We help customers plan the link, the power, and the host before they commit." - Alwin Vincent, Product Manager, Vadzo Imaging.

Applications for High Resolution Color Imaging on Moving and Fixed Platforms

Automation and Robotics

Robots, vehicles, and factory cells carry camera units on moving parts, far from their compute modules. The Armor-2020CRS-FPD3 works as an Autonomous mobile robot's FPD-Link III Camera for navigation, docking, and wide-area awareness, and as an unmanned ground vehicle's FPD-Link III Camera on rugged platforms where a thin coaxial cable replaces a bundle of wires. Fast motion can skew a rolling shutter frame, so a short exposure and a damped mount help, and teams should check weight and connector retention.

Several units around a vehicle build a view of its surroundings, and an inspection station needs detail at a fixed place. The module serves as a surround view system's FPD-Link III Camera when units on a multi-port deserializer are synchronized, with the total data planned for the host, and as an Industrial inspection FPD-Link III Camera where the 20MP frame reveals small defects. A low-resolution mode keeps the frame rate high when a line moves fast.

Smart City Solutions

Junctions, gantries, and toll points need detail at a distance and a cable that carries power and data to a pole. The module serves as an intelligent transportation systems FPD-Link III camera, where one unit covers a wide approach and a crop reads plates and signs, and its back-illuminated pixels help at dusk. Teams should confirm weatherproofing and the temperature range for roadside use, and plan surge protection for poles in open areas. In the illustrative example, a 5.6 millimeter lens lets one unit read plates 0.3 meters wide across a field about 38 meters wide at 30 meters.

Security and Surveillance

Perimeters and campuses need wide coverage with enough detail to identify what appears. The camera works as a Smart surveillance FPD-Link III Camera where 20MP lets one unit cover an area that would otherwise need several, and one cable simplifies mounting on masts and walls. Privacy rules apply to recorded video and belong to the operator.

Frequently Asked Questions

Q: What is FPD-Link III?

A: Vadzo Imaging explains that FPD-Link III is a serializer and deserializer link from Texas Instruments. A serializer on the camera turns the parallel output of the image sensor into a fast serial stream, which travels over a single coaxial cable to a deserializer on the host, where it becomes a standard camera interface again. Control commands travel back on the same cable, and power can share it. It lets a camera sit meters from its computer, and teams should confirm the details for the exact devices in use.

Q: Can one FPD-Link III link carry a 20MP video stream?

A: It depends on the frame rate and the format. The higher-speed devices carry video at a forward rate of about 4 gigabits per second. A 20MP frame at 12 bits per pixel is about 236 million bits, so 15 frames per second needs about 3.5 gigabits per second and fits, while 30 frames per second needs about 7.1 gigabits per second and does not. These figures are illustrative, and Vadzo Imaging recommends confirming the available modes and choosing the frame rate to match the link.

Q: What does a deserializer do on an NVIDIA Jetson system?

A: A Jetson module reads camera modules through MIPI CSI-2 lanes, and a serial camera link is not MIPI CSI-2. A deserializer board receives the serial stream from the cable, converts it back into MIPI CSI-2, and connects to the module. Some boards accept several camera links at once, and the total data must fit the lanes of the module. Vadzo Imaging helps customers choose the board and confirm the drivers for the Orin module they use.

Q: How does power travel over the camera cable?

A: In a single-cable design, the supply puts power onto the same coaxial cable that carries video and control, and the camera takes it off at the other end. A long cable loses voltage as current flows. For example, 1.5 ohms of round-trip resistance drops about 0.4 volts at 0.25 amperes, so the camera and the supply must tolerate it. Vadzo Imaging recommends checking the power budget and the voltage range for the real cable length.

Q: Why should integrators choose Vadzo Imaging as their 20MP FPD-Link III camera manufacturer?

A: Vadzo Imaging offers more than a camera module built around a capable sensor. Integrators receive a 20MP color module with a single-cable design, low-latency streaming, multi-camera readiness, and support for NVIDIA Jetson Orin platforms, with candid guidance on link bandwidth, voltage drop, and the details to confirm in the documentation, plus engineering support for deserializer selection, lens selection, firmware customization, and enclosure design. Vadzo Imaging maintains evaluation kits with no minimum order requirement, so teams can test on their own platform before committing to volume production.

Availability

The Armor-2020CRS-FPD3 20MP Color FPD-Link III Camera, built on the Onsemi AR2020 sensor, is available now for evaluation and production orders. Evaluation kits include the camera module, a cable, a deserializer board, and platform documentation, with no minimum order requirement. Integration teams can test frame rates against their own link, measure voltage drop on their own cable, compare the full resolution and reduced modes in dim light, and check multi-camera synchronization on their own NVIDIA Jetson Orin module before committing to a production bill of materials, which tells them more than a datasheet comparison alone. Teams that need a different lens, cable length, or deserializer configuration can ask Vadzo to review the setup. Browse the full range of camera options at Vadzo's website or discuss OEM integration requirements.

About Vadzo Imaging

Vadzo Imaging is a global provider of embedded vision solutions and delivers high-performance camera technologies and imaging platforms for applications in robotics, industrial automation, UAVs, edge AI, and medical systems. Its products are designed for seamless integration with leading embedded platforms, including NVIDIA Jetson, Rockchip, Raspberry Pi, and NXP i.MX. Vadzo supports customers through hardware customization, firmware development, and module-level drivers, enabling faster development and deployment of vision based systems across MIPI, USB, GigE, Wi-Fi, GMSL2, FPD-Link III, and SerDes camera interfaces.

Media Contact

Alwin Vincent
Vadzo Imaging
Email: alwin@vadzoimaging.com
LinkedIn: Vadzo Imaging
YouTube: Vadzo Imaging
X: Vadzo Imaging

SOURCE: Vadzo Imaging



View the original press release on ACCESS Newswire

Report this content

If you believe this article contains misleading, harmful, or spam content, please let us know.

Report this article